Epson ET-15000 Won’t Power On: Troubleshooting Steps and Solutions

Question:

Why won’t my Epson ET-15000 printer turn on? I’ve tried resetting it and changed the power cord, but nothing seems to work. Any advice?

Answer:

Thank you for contacting us! At BCH Technologies, we really appreciated your thumbs up to our engagement and content or even both (https://youtube.com/@bchtechnologies). We are always looking for feedback, and your insight will be crucial in improving our technical skills.

You have followed some steps to resolve your Epson ET-15000 printer issue. Here are A couple more things you can troubleshoot:

1. Check the Power Outlet

First, make sure the outlet is working. Try using a different device, such as a lamp. If the outlet is not working, try relocating your printer to another power outlet to set aside the possibility of a problematic outlet.

2. Check the Power Supply Unit (PSU)

To accomplish this task, you'll need to partially disassemble the printer to access the power supply unit (PSU). After removing the PSU, check it for damage, such as frayed wires or scorch marks. You can test the voltage output with a multimeter to see if it is within the expected limit. This is important, as failing to install the PSU will render your printer useless and prevent it from powering on.

Video on How to Uncase Epson Printer, which will give you more insight about what is inside the printer: How to Uncase Epson Printer https://youtu.be/iLdbI44EJ4o

3. Perform a Hard Reset

Sometimes a hard reset can correct power related problems.

Now, could you disconnect your printer from the power outlet?

Wait for the device to power off and reset in 10-15 minutes.

Could you connect it again to the power source of the printer and try turning on the printer?

4. Look Into Internal Power Issues

When the hard reset did not work, you could try checking the internal chassis connections. The most common problem is a Flat Flexible Cable (FFC) connecting various printer parts. Could you ensure the control panel cable is connected firmly without any visible damage? Furthermore, you might have to remove and check the mainboard. However, if there is damage, it may be possible to repair the mainboard and send it to a diagnostic service.

5. Firmware Corruption

Sometimes a printer will make it through its life cycle only to have the firmware get screwed up, preventing the unit from booting. This can sometimes be fixed by reinstalling or updating the firmware, but only if your printer is going even that far from the point. Following the device's responsiveness, if it remains unresponsive step, this will not be applicable.

6. Contact Epson Support

If you are under warranty, or even if not contacted by Epson customer service. Suppose they do not have any easy fix. In that case, they may provide some additional troubleshooting or schedule a repair that will most likely be offered at a lower cost should it be deemed the problem is a manufacturing defect.

7. Mainboard troubleshooting: If the problem is at least power-on in the Epson ET-15000 printer, especially in mainboard conditions, then after confirming everyday external phenomena such as cable and electricity… Helper: charm Check the voltage with a multimeter of the power supply unit (PSU) to ensure it delivers at the correct voltage, as that could be another fault source. If the issue occurs, then the PSU is fine, and you must look for visible damage on the mainboard in the form of blown capacitors, burn marks, or lost solder joints. If these are good, then one of the miniature fuses on the mainboard may have blown, preventing power from going there, so you must check these for continuity. Check the flat flexible cables (FFC) between the Mainboard and any other component for rips or loose connections. Any firmware corruption may brick the board, and a multimeter to test voltage around significant parts of the mainboard could reveal short circuits or broken components. Sometimes, the primary IC of the electronic explodes, and then the whole PCB fails if it is more economical to replace the PCB instead of repairing all components individually. Check for short circuits and use a multimeter on continuity mode to find and replace defective components. If these steps do not help, you might need to replace the mainboard altogether – by purchasing a new or refurbished one or sending it in for service. Take pictures before disassembly to facilitate reassembly (sic), employ ESD protection, and refer to the service manual for complete diagrams. Since replacing the mainboard is expensive, then it may be worthwhile to ask whether repairing or simply buying a new printer would be more cost-efficient.

8. Consult a Local Repair Shop

If none of those as mentioned above solutions help and your printer is out of warranty, you should take it to the nearby repair center. These could indicate problems with the internal power supply or even the motherboard, which can be rugged for untrained individuals to fix.

Printer-related issues are among the most complex problems to solve because they are hands-on in practice. As a result, we can only deal with remote troubleshooting after the guidelines or offer assistance for printer repair. However, we provide an in-person diagnosis and repair service at our local diagnostic center checkout via Printer Repair Service (https://bchtechnologies.com/printer-repair-service). Due to the high volume of inquiries, evaluation salvers are first come, first served; also, be prepared to wait weeks before you get your printer in for diagnostics. If you love having a DIY project or do not live close to one of our locations- We now offer mail-in (or local drop-off) services for whole-printer and specific part repairs!

Our rates may be less competitive, but we encourage everyone to take an online course first or watch tutorials on YouTube. You can start on our YouTube channel's home page. (https://youtube.com/@bchtechnologies) Accessible videos are searchable using the search feature next to "About" in the menu bar. We get many questions throughout the day, and one of the fastest ways to find some of the answers- both we provide and those from other creators- is searching on YouTube.

Again Thank You For Reaching Out I Hope This Will Fix Your Printer Issue. Feel free to contact us in case you need any help or advice.